Pitot-static: which instrument is lying?Lesson 2about 9 minutes
The blocked static port
A frozen altimeter is obvious. The airspeed error that comes with it is not, and on final approach it points you the wrong way.
Warm-up
Score: 0 / 0 · 0 of 2 answered
Before anything new. Answer without opening lesson 0001.
The airspeed indicator is misbehaving. The altimeter and VSI both agree with what you see outside. Which side of the system failed?
Only the airspeed indicator is plumbed to the pitot tube. Two working instruments on the static line clear the static line.
Which pressure source do all three pitot-static instruments share?
The static port. That is why a static blockage takes down all three at once, and why a pitot blockage can only reach the airspeed indicator.
The situation this solves
You are on a long descent into your home field. The altimeter has stopped moving. You notice, you file it away, and you keep flying, because the airplane is fine and you are busy. What you have not noticed is that the airspeed indicator is now reading roughly thirty knots faster than you are actually going, and the error is growing every hundred feet you descend.
So you see 90 knots on short final and think you are fast. You raise the nose. You are actually at 60 and slowing.
That is the accident this lesson is meant to prevent. The frozen altimeter is the warning. The airspeed error is the thing that hurts you.
Why the airspeed indicator goes wrong at all
It should not be obvious. The pitot tube is clear, ram air is arriving normally, and the airspeed indicator is the one instrument that has a working input. But it does not display a pressure. It displays a subtraction.
What the ASI actually computes
indicated airspeed ← pitot pressure − static pressure
The pitot side is live and correct. The static side is a sealed sample of the air from wherever you were when the port plugged. You are subtracting a memory.
From there it falls out in one step. Air pressure rises as you descend.
- Descend below the blockage altitude. Ram pressure is now built on top of a higher ambient pressure, but you are still subtracting the old, lower sample. You subtract too little. Airspeed reads high.
- Climb above it. Ambient pressure has fallen, but you are still subtracting the old, higher sample. You subtract too much. Airspeed reads low.
The altimeter and VSI need no derivation. The altimeter reads the static pressure directly, so a frozen sample means a frozen altitude. The VSI reads the rate of change of static pressure, and a sealed line has no rate of change, so it settles to zero and stays there. Source: FAA PHAK, Chapter 8.
How big is the error?
Bigger and faster than most people expect, and this is the part worth feeling rather than reading. The simulator below computes indications from the standard atmosphere, so the numbers are the real ones.
The static port is sealed at 5,000 feet with the airplane truly flying 100 knots. Drag the airplane away from that altitude and watch the airspeed needle.
Roughly a thousand feet of altitude is worth about an inch of mercury of pressure. The ram pressure at 100 knots is worth about half that. So a few hundred feet either side of the blockage is enough to move the airspeed needle further than any normal flight condition ever would. There is no gentle version of this failure.
The fix: alternate static source
In most 172s a knob on the lower panel, marked
ALTERNATE STATIC AIR, opens the static line to the cabin instead
of the outside port. Pull it and all three instruments come back.
They come back slightly wrong, and in a predictable direction. Air moving over the fuselage, plus leakage around doors and windows, holds the cabin at a marginally lower pressure than the outside air. A lower static pressure means a smaller number to subtract, and a higher altitude on the altimeter's scale.
On alternate static
Everything reads high. Altimeter high, airspeed high, and a brief false climb indication on the VSI at the moment you pull the knob.
Try the third button in the simulator above and compare it against the truth line.
Two practical consequences. Cabin vents and windows change the cabin pressure, so the POH correction only holds in the configuration the POH specifies. And the correction values differ between 172 models, so the number that matters is the one in the handbook for the tail number you are flying, not one from the internet.
What to carry away
The trapped static pressure is a memory of an altitude. Fly below that memory and the airspeed reads high. Fly above it and the airspeed reads low. Pull the alternate static source and everything reads a little high.
The dangerous case is the descent, because a high airspeed reading invites you to slow down at exactly the moment you cannot afford to.
Quiz
Score: 0 / 0 · 0 of 5 answered
Your static port plugs at 6,000 ft. You descend to 4,000 ft holding a genuine 90 knots. What does the airspeed indicator show?
Below the blockage altitude the outside pressure is higher than the trapped sample, so the instrument subtracts too little and reads high. This is the dangerous direction: it tempts you to slow down on the approach.
Same blockage at 6,000 ft. You climb to 8,000 ft at a genuine 90 knots. What does the airspeed indicator show?
Above the blockage the outside pressure has fallen below the trapped sample, so the instrument subtracts too much and reads low. Less immediately dangerous, because it pushes you toward flying faster.
Why does the VSI settle on zero when the static port blocks, rather than freezing at whatever rate it was showing?
The VSI displays the rate at which static pressure is changing. A sealed line has a constant pressure, so the calibrated leak equalises and the needle falls to zero. The altimeter freezes, but the VSI returns to centre.
You pull the alternate static source. Which way do the indications move?
Cabin pressure sits slightly below outside pressure, and a lower static pressure means a higher indication on both the altimeter and the airspeed indicator. Apply the POH correction and the cabin configuration it assumes.
Your altimeter is frozen but the airspeed still looks completely reasonable. What is the most likely explanation?
With a blocked static port the airspeed error is driven entirely by how far you are from the blockage altitude. Sitting at that altitude, the airspeed is correct. It goes wrong the moment you climb or descend, which is exactly when you stop watching it.
Read next
- FAA Pilot's Handbook of Aeronautical Knowledge, Chapter 8: Flight Instruments — the blocked static system section and the alternate static source discussion.
- Your POH, Section 3. Find the alternate static source procedure and the correction table, and note the cabin configuration it assumes.
Take this lesson home
Scan the code or type the link to work through the lesson and its quiz at your own pace.
buildswithmorgan.com/learn/aeronautical/the-blocked-static-port/
Your answers are saved only in this browser, so you can pick up where you left off.