Pitot-static: which instrument is lying? · Reference
Reference card
Cessna 172, conventional panel. Print this. Keep it in the flight bag.
The plumbing
| Instrument | Pitot line | Static line | Measures |
|---|---|---|---|
| Airspeed indicator | yes | yes | Ram pressure minus static pressure |
| Altimeter | no | yes | Static pressure against a sealed aneroid |
| Vertical speed indicator | no | yes | Rate of change of static pressure |
The rule
The airspeed indicator is the only instrument connected to the pitot tube. All three are connected to the static port.
One instrument wrong, two right, means the pitot side. All three wrong means the static side.
Failure table
| Failure | Airspeed | Altimeter | VSI |
|---|---|---|---|
| Pitot ram inlet blocked, drain hole open |
Drops to zero | Normal | Normal |
| Pitot inlet and drain both blocked |
Acts like an altimeter: reads high in a climb, low in a descent |
Normal | Normal |
| Static port blocked | Reads low in a climb, high in a descent |
Frozen at the blockage altitude | Falls to zero and stays there |
The pitot drain hole is the tiebreaker. It vents the pitot line to ambient pressure, so with the ram inlet plugged and the drain clear the diaphragm sees static on both sides and the needle collapses to zero. Plug both and the line traps a pressure sample, which then gets compared against a static pressure that keeps changing with altitude. Source: Boldmethod.
Why a static blockage moves the airspeed needle
The airspeed indicator displays a subtraction, not a pressure:
pitot pressure − static pressure. With the static line
sealed, the pitot side stays live while the static side is a stale sample of the air at
the blockage altitude. You are subtracting a memory.
- Below the blockage altitude ambient pressure is higher than the trapped sample. You subtract too little, so airspeed reads high.
- Above it ambient pressure is lower. You subtract too much, so airspeed reads low.
The error is large. A thousand feet is worth roughly an inch of mercury, while the ram pressure at 100 knots is worth about half that, so a few hundred feet off the blockage altitude moves the needle further than any normal flight condition would.
Static blockage: what to do
- Confirm it. Altimeter frozen and VSI pinned at zero while the airplane is demonstrably climbing or descending is the signature.
- Open the alternate static source. In most 172s this is a knob on the lower
panel, marked
ALTERNATE STATIC AIR. Pull it. - Expect the indications to shift. Cabin pressure is normally slightly lower than outside air, so on alternate static the altimeter and airspeed typically read high.
- Configure the cabin the way the POH says. Cabin vents and windows change the pressure the alternate source sees, so the correction only holds in the stated configuration.
- Apply the POH correction values. These differ between 172 models. Read the handbook for your tail number rather than a number from the internet.
If there is no alternate static source
Breaking the glass on the VSI vents the static system into the cabin. The VSI is destroyed and reads backwards afterwards, but the altimeter and airspeed indicator become usable again. This is a last resort, and only for an instrument-critical situation.
Pitot blockage: what to do
- Pitot heat on. Ice is the failure mode that occurs in flight, and heat is the only in-flight fix.
- Fly pitch and power. Known attitude plus known power setting produces a known airspeed. This is the actual mitigation, and it works regardless of the cause.
- Cross-check with GPS groundspeed, corrected for wind, as a rough sanity check.
Catch it on the ground
- Pitot cover removed, and the ram inlet and the drain hole both clear. Look into them. Mud dauber wasps build nests in pitot tubes.
- Static ports clear on both sides of the fuselage, and free of wax, paint, or tape.
- Pitot heat draws current when switched on. Check the ammeter, or feel the tube briefly, and do not hold on.
- Altimeter set to field elevation reads within 75 feet of the published elevation.
- During the takeoff roll: "airspeed alive." This is the last chance to catch a blocked pitot tube before it matters. No needle movement by the time you would normally see 40 knots means abort.