Rubik's Cube: a solve that staysLesson 5about 14 minutes
The second layer edges
Two thirds of the cube, from one algorithm and its mirror image.
Thirty seconds, from memory
The first-layer corner, in one sentence: which layer does a white corner start in, which layer does it end in, and what do you do to get it there?
Say it out loud first, then check
It starts in the top layer, above its own slot, and ends in the bottom layer. U until it sits directly above the slot its three colours name, then repeat R U R' U' until it drops in — one, three or five times. A corner already stuck in the bottom layer gets one repetition to eject it upward first.
1. Which four pieces
The middle layer has no corners — just four edges: green-red, red-blue, blue-orange and orange-green. They are exactly the four edges carrying neither white nor yellow, and with white already down, that reduces to one test you can run at a glance.
A middle edge is any edge with no yellow on it. If an edge in the top layer shows yellow anywhere, it belongs in the last layer — leave it. If it shows no yellow, it belongs in the middle layer, and this lesson puts it there.
Build the first layer, hold it white down, yellow up, and turn U slowly all the way round. Point at each of the four top edges and say “middle” or “last”. You should find some of each.
2. The tool, before the sequence
Hold the cube so the slot you are filling is the front-right one, at the middle of the cube. The sequence comes in two halves, and each half is a shape you already own.
| Half | What it is | What it does |
|---|---|---|
| U R U' R' | The Lesson 4 opener, inverted | Lifts the bottom-front-right corner out into the top layer, opening the column |
| U' F' U F | The same shape, mirrored onto the front face | Carries the edge down into the front-right slot and drops the corner back beneath it |
Written out, that is the right insert:
Inverting R U R' U' gives U R U' R' — the move stack unwound, order reversed and every direction flipped, which is the tool from Lesson 1. Mirroring that onto the front face swaps R for F and flips the directions again, which is U' F' U F. Nothing here is a new string to memorise.
Checked, not assumed, against the cube model behind this page’s simulator: over 20,000 random positions with a correctly aligned edge on top, the insert seated it in its slot every time, and the first layer came back intact every time. After the first half, the bottom-front-right corner was up in the top layer in 20,000 of 20,000 — the “opens the column” claim is a measurement, not a metaphor.
3. The left insert is the same thing in a mirror
Reflect the right insert left-to-right. Every R becomes an L, the front face stays the front face, and every direction reverses:
This fills the front-left slot instead. Same two halves, same jobs: open the bottom-front-left column, carry the edge in, close it.
4. The rule
Find a top-layer edge with no yellow. Turn U until its front sticker matches the front centre — the piece now points at the face it half belongs to. Then look at its top sticker:
- Top sticker matches the right centre → right insert.
- Top sticker matches the left centre → left insert.
That is the whole decision, and it is a decision you can derive rather than recall: the edge has two colours, one is now facing its own centre, and the other names the only side it can belong to. There is no third option — an edge with no yellow that shows a matching front sticker must go right or left.
5. The stuck case
Sooner or later no top edge is usable, because the remaining middle edges are already down in the middle layer — in the wrong slot, or in the right slot the wrong way round. Same answer as the stuck corner: get it out first.
Turn the cube so the offending edge is at the front right, then run the right insert once with whatever happens to be on top. The stuck edge is thrown up into the top layer, where it becomes an ordinary case. The same works on the left with the left insert.
Tested over 7,473 positions with a wrong or flipped edge in the front-right slot: one right insert ejected it into the top layer in every case, with the first layer intact afterwards every time. 7,525 front-left cases behaved identically under the left insert.
6. Right or left?
Six rounds. The marked edge is at the front top, already aligned — or it is a last-layer edge that should be left alone. Call it. Answering applies the insert, so you see straight away where the piece ended up.
7. Practise the whole step
This starts you with the first layer finished and everything above it scrambled — the position you are in at the end of Lesson 4. Get Second layer to 4 without letting First layer drop below 8.
Before the next lesson
- Do three full two-layer solves. Scramble, cross, corners, middle edges, scramble again. Say each edge’s two colours and which slot they name before you insert it — that is the habit that keeps this reconstructible.
- Derive it once a day. Rather than reciting the right insert, rebuild it: opener inverted, then the same shape mirrored onto the front. If you can do that cold, the algorithm cannot decay.
- Watch: J Perm’s Second Layer step. He gives the same two algorithms, presented as strings to memorise — worth seeing as a second route to the same target.
- Keep: the Second Layer card. After a gap, read that, not this.
- The cube stays out. Still the instruction that matters most.
Quiz
Score: 0 / 0 · 0 of 5 answered
Answer from memory, then check.
Which top-layer edges belong in the middle layer?
With white already down, a middle edge is any edge showing no yellow. An edge with yellow belongs in the last layer.
You lined up the edge's front sticker with the front centre. Its top sticker matches the right centre. Which insert?
The top sticker names the side the edge belongs to. Right centre, right insert.
What is the first half of the right insert, U R U' R'?
Reverse the opener and flip every direction. It lifts the bottom-front-right corner out and opens the column.
How do you get the left insert from the right one?
The left insert is the right insert in a mirror, so it is one thing to learn, not two.
A middle edge sits in its slot the wrong way round. What do you do?
Same answer as the stuck corner. Get it out first. It becomes an ordinary case in the top layer.
Read next
Next lesson: the yellow cross — the first step of the last layer, where you stop placing pieces one at a time and start moving several at once.
Take this lesson home
Scan the code or type the link to work through the lesson and its quiz at your own pace.
buildswithmorgan.com/learn/rubiks-cube/the-second-layer-edges/
Your answers are saved only in this browser, so you can pick up where you left off.